Zero bias terahertz and subterahertz detector operating at room temperature
In this paper, the experimental study of the terahertz and subterahertz hot electron bolometer based on narrow-gap semiconductor compound Hg₁₋xCdxTe is presented. The measurements were performed in the temperature range from 77 to 300 K at various operating mode and frequency. The estimated value...
Збережено в:
| Дата: | 2010 |
|---|---|
| Автори: | , , , , , |
| Формат: | Стаття |
| Мова: | English |
| Опубліковано: |
Інститут фізики напівпровідників імені В.Є. Лашкарьова НАН України
2010
|
| Назва видання: | Semiconductor Physics Quantum Electronics & Optoelectronics |
| Онлайн доступ: | http://dspace.nbuv.gov.ua/handle/123456789/118225 |
| Теги: |
Додати тег
Немає тегів, Будьте першим, хто поставить тег для цього запису!
|
| Назва журналу: | Digital Library of Periodicals of National Academy of Sciences of Ukraine |
| Цитувати: | Zero bias terahertz and subterahertz detector operating/ N. Momot, V. Zabudsky, Z. Tsybrii, M. Apats'ka, M. Smoliy, N. Dmytruk // Semiconductor Physics Quantum Electronics & Optoelectronics. — 2010. — Т. 13, № 2. — С. 166-169. — Бібліогр.: 11 назв. — англ. at room temperature |
Репозитарії
Digital Library of Periodicals of National Academy of Sciences of Ukraine| id |
irk-123456789-118225 |
|---|---|
| record_format |
dspace |
| spelling |
irk-123456789-1182252017-05-30T03:04:39Z Zero bias terahertz and subterahertz detector operating at room temperature Momot, N. Zabudsky, V. Tsybrii, Z. Apats’ka, M. Smoliy, M. Dmytruk, N. In this paper, the experimental study of the terahertz and subterahertz hot electron bolometer based on narrow-gap semiconductor compound Hg₁₋xCdxTe is presented. The measurements were performed in the temperature range from 77 to 300 K at various operating mode and frequency. The estimated value of the noise equivalent power at room temperature for detector proposed was 1.3·10⁻⁸ W/Hz¹/² and 5.4·10⁻⁹ W/Hz¹/² at bias current I = 1 mA and I = 0, respectively. 2010 Article Zero bias terahertz and subterahertz detector operating/ N. Momot, V. Zabudsky, Z. Tsybrii, M. Apats'ka, M. Smoliy, N. Dmytruk // Semiconductor Physics Quantum Electronics & Optoelectronics. — 2010. — Т. 13, № 2. — С. 166-169. — Бібліогр.: 11 назв. — англ. at room temperature 1560-8034 PACS 07.57.Kp, 72.20.Ht http://dspace.nbuv.gov.ua/handle/123456789/118225 en Semiconductor Physics Quantum Electronics & Optoelectronics Інститут фізики напівпровідників імені В.Є. Лашкарьова НАН України |
| institution |
Digital Library of Periodicals of National Academy of Sciences of Ukraine |
| collection |
DSpace DC |
| language |
English |
| description |
In this paper, the experimental study of the terahertz and subterahertz hot
electron bolometer based on narrow-gap semiconductor compound Hg₁₋xCdxTe is
presented. The measurements were performed in the temperature range from 77 to
300 K at various operating mode and frequency. The estimated value of the noise
equivalent power at room temperature for detector proposed was 1.3·10⁻⁸ W/Hz¹/² and
5.4·10⁻⁹ W/Hz¹/² at bias current I = 1 mA and I = 0, respectively. |
| format |
Article |
| author |
Momot, N. Zabudsky, V. Tsybrii, Z. Apats’ka, M. Smoliy, M. Dmytruk, N. |
| spellingShingle |
Momot, N. Zabudsky, V. Tsybrii, Z. Apats’ka, M. Smoliy, M. Dmytruk, N. Zero bias terahertz and subterahertz detector operating at room temperature Semiconductor Physics Quantum Electronics & Optoelectronics |
| author_facet |
Momot, N. Zabudsky, V. Tsybrii, Z. Apats’ka, M. Smoliy, M. Dmytruk, N. |
| author_sort |
Momot, N. |
| title |
Zero bias terahertz and subterahertz detector operating at room temperature |
| title_short |
Zero bias terahertz and subterahertz detector operating at room temperature |
| title_full |
Zero bias terahertz and subterahertz detector operating at room temperature |
| title_fullStr |
Zero bias terahertz and subterahertz detector operating at room temperature |
| title_full_unstemmed |
Zero bias terahertz and subterahertz detector operating at room temperature |
| title_sort |
zero bias terahertz and subterahertz detector operating at room temperature |
| publisher |
Інститут фізики напівпровідників імені В.Є. Лашкарьова НАН України |
| publishDate |
2010 |
| url |
http://dspace.nbuv.gov.ua/handle/123456789/118225 |
| citation_txt |
Zero bias terahertz and subterahertz detector operating/ N. Momot, V. Zabudsky, Z. Tsybrii, M. Apats'ka, M. Smoliy, N. Dmytruk // Semiconductor Physics Quantum Electronics & Optoelectronics. — 2010. — Т. 13, № 2. — С. 166-169. — Бібліогр.: 11 назв. — англ.
at room temperature |
| series |
Semiconductor Physics Quantum Electronics & Optoelectronics |
| work_keys_str_mv |
AT momotn zerobiasterahertzandsubterahertzdetectoroperatingatroomtemperature AT zabudskyv zerobiasterahertzandsubterahertzdetectoroperatingatroomtemperature AT tsybriiz zerobiasterahertzandsubterahertzdetectoroperatingatroomtemperature AT apatskam zerobiasterahertzandsubterahertzdetectoroperatingatroomtemperature AT smoliym zerobiasterahertzandsubterahertzdetectoroperatingatroomtemperature AT dmytrukn zerobiasterahertzandsubterahertzdetectoroperatingatroomtemperature |
| first_indexed |
2025-07-08T13:35:18Z |
| last_indexed |
2025-07-08T13:35:18Z |
| _version_ |
1837085983878676480 |
| fulltext |
Semiconductor Physics, Quantum Electronics & Optoelectronics, 2010. V. 13, N 2. P. 166-169.
© 2010, V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine
166
PACS 07.57.Kp, 72.20.Ht
Zero bias terahertz and subterahertz detector operating
at room temperature
N. Momot*, V. Zabudsky, Z. Tsybrii, M. Apats’ka, M. Smoliy, N. Dmytruk
V. Lashkaryov Institute of Semiconductor Physics, NAS of Ukraine,
41, prospect Nauky, 03028 Kyiv; e-mail: momotnatasha@isp.kiev.ua
Abstract. In this paper, the experimental study of the terahertz and subterahertz hot
electron bolometer based on narrow-gap semiconductor compound Hg1-xCdxTe is
presented. The measurements were performed in the temperature range from 77 to
300 K at various operating mode and frequency. The estimated value of the noise
equivalent power at room temperature for detector proposed was 1.3·10–8 W/Hz1/2 and
5.4·10–9 W/Hz1/2 at bias current I = 1 mA and I = 0, respectively.
Keywords: THz radiation, bolometer, hot-carrier effect.
Manuscript received 02.02.10; accepted for publication 25.03.10; published online 30.04.10.
1. Introduction
Currently, there is a substantial interest in a part of the
spectrum located between microwave and optical ranges.
Commonly this frequency band is defined as 0.1-10 THz
and called “the terahertz region”. The attention to
terahertz radiation is caused by its unique properties
because of which it finds a wide use for science and
technology [1].
Particularly, it is of great interest to create the
detection array for terahertz imaging. Heterodyne
detectors are the most sensitive in the terahertz
region [2], but creating terahertz heterodyne arrays is
associated with some difficulties: i) because of all
array elements require a common local oscillator, the
number of elements is limited of its power;
ii) heterodyne terahertz detectors are mainly based on
superconductors now (semiconductor-insulator-
semiconductor structures or hot electron bolometers) [3]
that are in need of cooling to the superconducting
transition temperature. Since open-cycle cooling systems
are awkward and expensive while closed-cycle cooling
systems are low-power, the cryogenic cooling limits the
expansion of the number of array elements, too.
Therefore, heterodyne terahertz detector arrays are
constructed now with a small number of elements (a few
tens) [4]. The direct-detection matrix receivers are
better in comparison with heterodyne detectors
concerning the number of elements expansion.
In this paper, a direct-detection terahertz and
subterahertz receiver based on narrow-gap
semiconductor compound Hg1-xCdxTe (MCT) is
investigated. This detector can operate at room
temperature, zero bias and have several micrometers
area. Therefore, compact terahertz detector array can
be created as based on this material.
2. Design of detector and experimental results
As basic material for manufacturing the THz detector, p-
type conductivity epitaxial films CdxHg1-xTe/CdZnTe
(x = 0.22-0.23) were used. These were grown using
liquid phase epitaxy technique providing carrier
concentration 3.61015 to 21016 cm–3 and thicknesses of
layers within the range 2-20 µm. Taking into account the
mechanical and electro-physical properties of CdHgTe,
the design and technological route of a multi-element
detector was developed.
The technological route of manufacturing this
structure consists of the following stages:
control of MCT layers quality by using optical
microscopy and IR-Fourier spectroscopy methods;
preliminary chemical preparation of MCT surface;
formation of CdTe passivation layer;
photolithography processes;
metallization through lift-off photolithography
method.
The surface of a detector active element has been
protected by CdTe thin film formed using the hot wall
epitaxy method. Metallic contacts to the active element,
which serve as antenna, have been placed on the
passivation layer. Etching the mesa-structures was used
(up to the high-resistance substrate) with the purpose of
short-circuit prevention between matrix elements. The
Semiconductor Physics, Quantum Electronics & Optoelectronics, 2010. V. 13, N 2. P. 166-169.
© 2010, V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine
167
Fig. 1. Scheme of THz antenna and microphoto of its central part that were made using high resolution optical microscopy. The
area 1 is the active element, 2 and 3 – metallic contacts.
electrical contacts between sensitive element and
antenna have been realized by chemical etching the
contact windows into the passivation layer. Special
bromic etchant has been picked up for etching these
passivation thin layers.
The detector matrix consists of 4×11 elements
(each of it has 10×50 µm2 active area and was connected
to the bow-tie like antenna with 568750 µm2 area). The
scheme and microphoto of the detector with antenna are
shown in Fig. 1.
The theory of the photoresponse mechanism of
such detector has been proposed in [5]. In this device,
the radiation heats electrons in the semiconductor,
whereas semiconductor lattice heating is absent. The
heating changes generation-recombination processes that
produce changes of the carrier number and of the
semiconductor resistance. A value of the semiconductor
hot electron bolometer response time is determined by
the carrier lifetime.
The response of Hg1-xCdxTe bolometer was
measured in the range of frequencies 0.037-1.58 THz
and in the temperature range from 77 to 300 K at various
detector bias currents. The experimental results
indicating that the detector is sensitive in the mentioned
range are presented in [6]. In addition, these results show
that the photoresponse of p-type Hg1-xCdxTe at zero bias
is higher than that of the n-type Hg1-xCdxTe.
In Fig. 2, the response of p-type MCT bolometer is
shown as the function of temperature for the acceptor
concentration Np = 7·1015 cm–3, mole fraction of CdTe
x = 0.2 and dimensions of the sensitive element
10×50×17 μm. At T = 77 K the value of photoresponse
at non-zero bias is several times higher than at I = 0 for
that sample. At the same time, at room temperature the
value of photoresponse is of the same order of
magnitude for I = 1 mA and I = 0.
Fig. 3 demonstrates the photoresponse of this
bolometer as the function of the detector current. The
deviation from linearity at close to zero biases is probably
caused by rectifying effect between semiconductor and
metallization. For example, in Fig. 4 the experimental
results for another sample response as the function of
detector current at T = 77 K and its I – V characteristic are
presented. For this sample, the detector sensitivity at zero
bias current even higher as compared to the non-zero bias.
As a rule, to characterize THz detectors, the noise
equivalent power (NEP) is used. NEP is the radiant
power needed to generate signal equivalent to noise. The
NEP can be calculated as:
2/1)(
NEP
fS
U
V
N
, (1)
where UN is the noise voltage, SV – detector voltage
sensitivity, Δf – pass bandwidth.
Semiconductor Physics, Quantum Electronics & Optoelectronics, 2010. V. 13, N 2. P. 166-169.
© 2010, V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine
168
100 150 200 250
-10
0
10
20
P
ho
to
re
sp
on
se
,
V
T, K
I=1 mA
I=-1 mA
I=0
Fig. 2. The bolometer response as a function of temperature.
The frequency of incident radiation is ν = 78 GHz. The
frequency of modulation is Δf = 360 Hz. The radiation flux
density is ~4.5 mW/cm2 in the place of sample location.
CdxHg1-xTe photoresistors are typically
characterized with the Johnson noise, generation-
recombination noise, and photon noise.
The mean-square power for Johnson’s noise is [7]:
fTkRU BJ 4
2
, (2)
where R is the sample resistance, kB is the Boltzmann
constant, T is sample temperature, Δf is a bandwidth for
the central frequency.
The spectral density of generation-recombination
noise current caused by interband transitions is of the
form [8]:
)1)(()(
)1(4
)(
22
00
2
00
00
22
pnpbn
pnbI
fS c
I , (3)
where pnb / is the mobility ratio, τ is the dominant
lifetime, Ic is the current, n0 and p0 refer to the total
numbers of electrons and holes in the sample of thermal
equilibrium. The generation-recombination noise voltage
is equal
-1 0 1
-10
0
10
20
30
P
ho
to
re
sp
on
se
,
V
I, mA
Fig. 3. The bolometer response as a function of detector
current at T = 77 K. The frequency of incident radiation is
ν = 78 GHz. The frequency of modulation is Δf = 360 Hz. The
radiation flux density is ~4.5 mW/cm2 in the place of sample
location.
-100 0 100
-1
0
1
I,
m
A
U, mV a)
-1 0 1
-10
-5
0
5
10
15
20
P
h
o
to
re
sp
o
n
se
,
V
I, mA b)
Fig. 4. The I-V characteristic and bolometer response as a
function of detector current at T = 77 K. The frequency of
incident radiation is ν = 130 GHz.
fRSU Irg
22
. (4)
For photon noise (the dispersion of falling to
sample photons number), the next expression can be
written [9]
eRNAU phn
21
η2 , (5)
where N is the photon flux from the T = 300 K
background hemisphere, e is the electron charge, η = 0.5
is the quantum efficiency of detector, and A is the
sensitive element area.
2
1 1
(
4
d
e
c
TN
kT
hc
. (6)
General noise is estimated using the following
formula:
222
phnJrg UUUU . (7)
The noise voltages in the sample were estimated
from Eqs (2)-(7) at Δf = 1 Hz and the results have been
summarized in Table 1.
At room temperature, generation-recombination
noise is higher than the other ones. Because of the
generation-recombination noise is apparent at the current
flow through the sample, its contribution can be
excluded by a zero bias mode.
Semiconductor Physics, Quantum Electronics & Optoelectronics, 2010. V. 13, N 2. P. 166-169.
© 2010, V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine
169
Table 1. Estimated noise voltages.
Noise type Т = 77 K Т = 300 K
Johnson’s noise 5.1·10–10 V 5.4·10–10 V
Generation-
recombination
noise
2·10–11 V 1.2·10–9 V
Photon noise 1.4·10–11 V 1.7·10–12 V
Given in Table 2 are the values of estimated noise
equivalent power for the detector currents I = 1 mA and
I = 0.
Table 2. Estimated NEP.
Detector
current, I
Т = 77 K Т = 300 K
1 mA 4·10–10 1.3·10–8NEP,
W/Hz1/2 0 8·10–10 5.4·10–9
Thus, because of the smaller noise, the detector
threshold sensitivity is higher at zero bias than at an
applied current despite a smaller photoresponse. The
estimated noise equivalent power of detector is
comparable with the NEP of other terahertz uncooled
devices [10, 11].
3. Conclusions
The semiconductor hot electron bolometer based on
narrow-gap Hg1-xCdxTe can be used for detection of
terahertz and subterahertz radiation. The noise
equivalent power of such detector that operates at room
temperature and zero bias is of the order of 10–9 W/Hz1/2,
thus multi-element terahertz detector can be created as
being based on it.
References
1. F P. Siegel, Terahertz technology // IEEE Trans.
Microwave Theory and Techniques 50(3), p. 910-
928 (2002).
2. F. Sizov, THz radiation sensors // Opto-Electron.
Rev. 18(1), p. 10-36 (2010).
3. Sheng-Cai Shi, Superconducting THz detectors and
their applications in radio astronomy // Terahertz
Science and Technology 1(4), p. 199-215 (2008).
4. I.I. Eru, Matrix multibeam reception of
submillimeter and infrared electromagnetic waves
(the state-of-the-art and trends) // Radio Physics
and Radio Astronomy 11(3), p. 298-307 (2006).
5. V. Dobrovolsky, F. Sizov, A room temperature, or
moderately cooled, fast THz semiconductor hot
electron bolometer // Semicond. Sci. Technol. 22,
p. 103-106 (2007).
6. F.F. Sizov, V. Dobrovolsky, V. Zabudsky,
Yu. Kamenev, N. Momot, and J. Gumenjuk-
Sychevska, mm- and THz-waves detector on the
base of narrow-gap semiconductors // Proc. SPIE
7309 (2009).
7. N.B. Lukyanchikova, Noise Research in
Semiconductor Physics. Gordon and Breach
Science Publishers, Amsterdam, 1999.
8. R.N. Sharma, K.M. van Vliet, Generation-recom-
bination fluctuations in mercury-cadmium telluride
// Phys. status solidi (a) 1, p. 765-773 (1970).
9. A. van der Ziel, Noise in Measurements. John
Wiley & Sons Inc., 1976.
10. El Fatimy, A. Delagnes, J.C. Younus, A. Nguema,
E. Teppe, F. Knap, W. Abraham, E. Mounaix,
Plasma wave field effect transistor as a resonant
detector for 1 terahertz imaging applications //
Optics Communs 282(15), p. 3055-3058 (2009).
11. J.L. Hesler, T.W. Crowe, Responsivity and noise
measurements of zero-bias Schottky diode
detectors // 18th Intern. Symp. Space Terahertz
Techn., Pasadena, 2007.
|